3Com 3C529 (TP)
3C529 EtherLink III MCA 
3C5X9X.EXE  V4.3 EtherDisk for 3C579 /3C529 Etherlink III  NIC 
5X9C32.EXE  ODI-32 driver for EtherLink III 3C5x9 adapters 
5X9UW.EXE Unsupported Unixware drivers for the 3C5X9 Ad 
5X9NW.EXE EtherLink III 3C5x9 family NetWare 2.x server drivers, and IPX.COM workstation shell driver, with LANPATCH utility. 

EtherDisk 6.1 for 3C529
3c509x1.exe EtherDisk #1 NDIS3 and NDIS4 miniport drivers for Win95/98 and NT 3.51/ 4.0.
3c509x2.exe EtherDisk #2 NW 3.X / 4.X, various DOS NOS, IBM OS/2, and packet driver

   The 3C529 MicroChannel NICs are partially supported. In Windows 95 and Windows NT, the NIC driver can be installed and removed, but the windows diagnostic program and tray icon are not loaded. To make configuration changes or test a 3C529, use the DOS diagnostic on diskette #2.

09-0399-002.pdf  3C529-TP/COAX Adapter Guide

3C529 / 3C529-TP
   3c529-TP with Motorola SB4100 Cable Modem
ADF Sections   (Common ADF, differs only in Tranceivers)


3C529 / 3C529-TP Etherlink III
@627C.ADF 3Com 3C529 Network Adapter 


Image from 3com
@627D.ADF - 3Com 3C529-TP Network Adapter 


Image from 3com

3C529-TP w/SB4100 Cable Modem
   Works just fine under NT 4. Using the included 3com Etherlink III MCA adapter drivers from the NT install CD. Just run a TP cable from the 3C529-TP to the SB4100 and voila, cable modem speeds.
  All I installed was TCP/IP, and of course, ZoneAlarm. You will need SP3 or greater for the updated network files (LDSYS?)
  I installed the drivers from EtherDisk 6.1, and I am getting about 384/120 depending on where I'm surfing to.

AdapterId 627C 3Com 3C529 Network Adapter
AdapterId 627D  3Com 3C529-TP Network Adapter
 

Enable/Disable Adapter
   Use the'disabled' setting if you are not using the adapter and enabling it causes a conflict with another device
    <" adapter enabled ">, adapter disabled

I/O Address Range
   The addresses in this range cannot be used by another installed device.
     <" 200h to 20Fh ">, 600h to 60Fh, A00h to A0Fh, E00h to E0Fh, 1200h to 120Fh, 1600h to 160Fh, 1A00h to 1A0Fh, 1E00h to 1E0Fh, 2200h to 220Fh, 2600h to 260Fh, 2A00h to 2A0Fh, 2E00h to 2E0Fh, 3200h to 320Fh, 3600h to 360Fh, 3A00h to 3A0Fh, 3E00h to 3E0Fh, 4200h to 420Fh, 4600h to 460Fh, 4A00h to 4A0Fh, 4E00h to 4E0Fh 

Interrupt Request Level
   This adapter's interrupt level can be shared with another installed device.  You may be able to improve performance by selecting a level that is not used by any other installed device.
    <" level 3 " >, 5 , 7 , 9, 10, 11, 12, 15

Boot ROM Address Range
   Range of addresses used by the boot PROM installed on the adapter.  The addresses in this range cannot be used by any other installed device
or software.  The size of the address range must correspond with the size of the boot ROM.  Select 'disabled' if no boot ROM is installed.
    <" disabled ">
(8K) C200-C3FF, C400-C5FF, C600C7FF, C800-C9FF, CA00-CBFF, CC00-CDFF, CE00-CFFF, D000-D1FF, D200-D3FF, D400-D5FF, D600-D7FF, D800-D9FF, DA00-DBFF, DC00-DDFF, DE00-DFFF
(16K) C000-C3FF, C400-C7FF, C800-CBFF, CC00-CFFF, D000-D3FF, D400-D7FF, D800-DBFF, DC00-DFFF
(32K) C000-C7FF, C800-CFFF, D000-D7FFF, D800-DFFF 

Transceiver Type (627C/529)
   Transceiver used by the adapter.  If you wish to connect to the adapter's
BNC connector, select 'on-board'.  If you wish to attach a drop cable from an external transceiver to the adapter's 15-pin AUI connector, select 'external'. 
    <" on-board (BNC) ">, external (AUI) 

Transceiver Type (627D/529-TP)
   Transceiver used by the adapter.  If you wish to connect to the adapter's
8-pin RJ-45 connector, select 'on-board'.  If you wish to attach a drop cable from an external transceiver to the adapter's 15-pin AUI connector,
select 'external'.
    < " on-board (RJ45) ">, external (AUI) 

9595 Main Page