Ultimedia Module PCB
77 Case, Rear
Ultimedia Adapter (to another page)
76/77 Model Codes
76/77 i/s Model Codes
Lacuna vs. Bermuda
Devil's in the Details
77 Bermuda Riser
9577 Multimedia Model Features
9577S Multimedia Model Features
77 5.25" Drive Bay Guides
Original 5.25" Drive Rail
5.25" 77 Drive Rail Hack
PCMCIA Adapter Mounting
9577 Drive Slide
9577 Air Baffle for Fixed Disk Drive Bay 4C
Air Baffle Pasteboard Hack
SCSI Controller Sets HD as 6,1 Instead of 6,0
77 Case, Front (40, 57 similar) Multimedia Model shown
Module (Image and some comments from William
R. Walsh) Original HERE
Both standard and MM control panels have a speaker.Only
the MM control panel has Microphone and Headphone jacks (1/4" stereo jacks).
The MM speaker (behind the grille) is rated 1.5 watts / 8 ohms as compared
to 0.5 watts at 4 or 8 ohms. The shape is an oval cone set into a square
The standard control panel lack the microphone, headphone and volume features.
Module PCB (outline and comments from
William R. Walsh) original HERE
U2 - Philips TDA1015 1-4 watt self contained power amplifier (datasheet)
I would assume that the connection to the sound card powers the onboard amplifier. With the sound card cable unplugged the volume control ceases to function and the speaker plays all beeps as a normal front panel would.
Have front facing away
Unscrew both thumbscrews
"Slap" the top of the case forward using your palms along the sides of the case
When the top of the case moves forward an inch and a half, pull up.
9576 and 9577 Model Codes
Dxx=Choice of OS
9576 and 9577 i/s Model Codes
Thanks for showing the EASY way, Oloruin!
Axx=Lacuna, On-board IDE, built-in S3 video
All the multimedia models include the following features:
Ed. I found NO
MM 76 models.
You can upgrade any current PS/2 76/77 or PS/2 56/57 with the new PS/2 Planar Upgrade. You'll gain all the advantages of the new 76/77 i and s systems. Current 76/77 systems will perform up to 38% faster while keeping everything else intact.
Devil's in the
The two broad classes of box designs that led to the 9576
Of course, the 855X were 80386DX or 80386SLC, so they used a completely different system board. The 9576 and 9577 used the same system board (=Bermuda), one with SCSI built into the board (=Bermuda). The 9576i and 9577i (Lacuna system board) were made in two different clock speeds -- 25MHz and 33MHz. Their system board FRU part numbers were:
25MHz only: 95G9691 (not streaming transfer
A 957Xs is only a 957Xi with a modified Future Domain SCSI
card added to one of the adapter slots on the bus riser card, to handle
internal/external SCSI devices.
9576 Bus adapter*
9556 Bus adapter*
8556 Bus adapter*
9577i/s 5-slot bus riser assembly
9577 Bus adapter riser
9557 Bus adapter riser
8557 Bus adapter riser
type 1 85F0056
So you see, it is important to know both the part number
and clock speed limitation of the Lacuna-type board, and to have the correct
bus riser card for the particular box/system board. In other words, you
cannot really upgrade a 957X to a 957Xi/s without changing the riser card
as well as the system board!
IBM 76 Security Cable Cover . Hmm, never seen one.
The pinout of the standard 9577 speaker/power switch module is
o IBM PS/2 8514 Display Adapter/A (#4054, 1887972)
o IBM PS/2 Micro Channel SCSI Adapter (#1005, 6451109)
o IBM PS/2 Micro Channel SCSI Adapter with Cache (#1018, 6451110)
o IBM Mwave WindSurfer-MCA Communication Adapter/A (#7058, 82G7058)
The IBM 1GB AT Hard Disk Drive (#2543, 70G8512) is supported with the following limitation: If you experience problems configuring this drive as the "master" with any other fixed disk drive in your system, reconfigure this drive as the "slave" drive.
Secured removable media via 2.88MB Electronic Eject Diskette Drive (optional)
77 5.25" Drive Bay Guides
Post- Notches on the reverse that fit into the drive bay walls.
Latch- Locks the guide onto the drive bay wall.
This was "fun". On this rail, the screw hole marked "R"
was the fixed hole, and it serves as the reference point for the important
surfaces. Note that the center-to-center distance is 3.115". Measured that
from a drive. One hole is usually slotted so there can be some variation
between mounting screw locations on drives.
5.25" 77 Drive Rail
PCMCIA Adapter mounting
I finally got around to installing the PCMCIA adapter in my 77s. The trick- mount the adapter on a 76/77 floppy tray. (Adapter MUST be in the stamped metal bay PN 64F1270) Remove the rail guides on the dive support stucture in the 77. (Catches are on the inner end) swap the guides to the other side and push them onto the mounting studs. Now turn the tray/adapter upside down and push it into the rails. Note that the two card ejection buttons are now on the left side of the adapter. Just happens to be the exact height to perfectly fit the bezel.
Fixed Disk Bay 4C Drive Slide 96F7775, 71G5706, 71G5708, 79F3300
Seems this is a little long for OAL for it to fit into the Model 90's lower drive bay.
The older 8557 and 9557 used a grey colored baffle, same FRU.
This was used in older systems with hot running drives in 4C. Modern 1" high drives should run cool enough without it, but if you want to run a 7,200RPM (or higher) drive in your 77, you MIGHT want to help cool it as much as possible.
PS/2 - 76/77 S Model Configures SCSI HD As 6,1
The 9576 or 9577 system configures the harddisk with a SCSI ID of 6,1 instead of 6,0. A POST error of 1047000 107 may also occur.
Problem Isolation Aids: