TRMAU1.EXE  Driver diskette 
TRMAU2.EXE Option diskette 

ADF Sections

Network Adapter LED Status 

Amber	Green	Explanation
Blinking  (500ms)	Blinking  (500ms)	The adapter is active and waiting for initialization.
Off	Off	Adapter initialization in progress, computer is powered off, or adapter is not active. Run LANAID and verify the adapter's configuration.
Off	Blinking  (80ms)	No problems detected during self-diagnostic  tests and adapter is waiting to open. If this occurs after adapter opens, this indicates adapter is closed.
Off	On	The adapter is open and operating correctly.
On	Off	The adapter self-diagnostics tests failed or there is a problem with the adapter.
Blinking  (80ms)	Off	The adapter is closed. The adapter failed to open, detected a wire fault or failed the auto-removal test.
Blinking  (80ms)	On	The adapter has detected beaconing or a hard error.

The Auto 16/4 Adapter transmits and receives data at a rate of either 4 or 16 Mbps over shielded twistet-pair (STP) or unshielded twisted-pair (UTP) cable. The Auto 16/4 Adapter can be installed in either an 8-bit or 16-bit slot. 

Note: EUROPEAN USERS - If the adapter is used with UTP cabling, you require cabling with a ferrite core (IBM P/N 60G6059 or equivalent) 

Cable Types Supported
  This advanced line of token ring cards meets all of the electrical transmitter and receiver requirements for 100 ohm, 120 ohm and 150 ohm cabling which requires no impedance matching devices at 4 or 16 Mbit/s speeds.  One port can drive any of the three types of cabling specified. 

Error Messages - 
0166nnx0 - Primary Adapter / 0167nnx0 - Secondary Adapter 
The values for nn are: 

80	Invalid testing mode requested
81	Primary Adapter not present
82	Alternate Adapter not present
85	Configuration compare failure
90	Adapter Test failure
91	Open phase test failure
92	Computer problem
93	Transmit or receive test failure
99	General error

the x represents the slot number of the adapter in error 

Primary or Alternate adapter
   Up to two Token-Ring Network adapters may be installed in this computer.  An adapter is either Primary (0A20-0A23), or Alternate (0A24-0A27).  If one Token-Ring Network adapter is installed, it may be either Primary or Alternate.  If two are installed, one must be defined as Primary and the other Alternate. 
    <"Primary" (0A20 - 0A23)>, Alternate (0A24 - 0A27) 

Adapter Data Rate
   You MUST set the adapter data rate to the same rate as the Token-Ring segment to which you are connecting the adapter if Autosense is set Off.  If Autosense is set On, this setting is used as an initial data rate to insert at after the configuration has changed. 
  It is recommended that you set the adapter rate the same as the Token-Ring segment to which you are conecting the adapter, even if Autosense is set to On. 
    <16 Mbps">, 4 Mbps 

Autosense
   This adapter can detect the ring speed of the Token-Ring Segment. When Autosense is on, the adapter will atempt to determine the ring speed to insert itself at.  When off, the 'Adapter Data Rate' setting determines the adapter data rate. 
    <"On">, Off 

ROM Address Range
   There are 12 possible 8K blocks used for accessing the ROM area of the Token-Ring adapter.  The preferred address is: CC000-CDFFF.  The ROM address selected must not be assigned for use by any other adapter or option and cannot be the same as the RAM address for this adapter. 
    <"CC000-CDFFF">, CE000-CFFFF, D0000-D1FFF, D2000-D3FFF, D4000-D5FFF, D6000-D7FFF, D8000-D9FFF, DA000-DBFFF, DC000-DDFFF, DE000-DFFFF, C8000-C9FFF, CA000-CBFFF 

RAM Size and Address Range
   There are 30 possible blocks of memory that can be assigned for accessing the RAM located on this adapter. The preferred RAM Size and Address Range for the adapter, which allows RAM Paging, is: 16 KB / D8000-DBFFF.  The RAM Address Range must not be assigned for use by any other adapter or option, and it cannot be the same as the ROM address for this adapter. (Ed. all 8K windows are commented out) 
    <"16 KB / D8000-DBFFF">, DC000-DFFFF, C0000-C3FFF, C4000-C7FFF, C8000-CBFFF, CC000-CFFFF, D0000-D3FFF, D4000-D7FFF 
   32 KB / D8000-DFFFF, C0000-C7FFF, C8000-CFFFF, D0000-D7FFF 
   64 KB / D0000-DFFFF, C0000-CFFFF 

Interrupt Level
   This adapter can operate on one of four interrupt levels: 2, 3, 10, or 11.  The preferred interrupt level is 2, but the adapter can operate on any of the four levels if necessary 
    < "Interrupt 2">, 3, 10, 11 

Enable or Disable RPL
   Ths adapter can be used in a medialess system by enabling RPL or vice versa when chosing DISABLED.  BEWARE:  if RPL is ENABLED, some high level software programs (eg.  some server software) may require that the adapter be configured as the primary adapter. 
  If your Token-Ring adapter has a separate RPL module socket, the Enable or Disable RPL option will have no effect" 
   <"Enabled">, Disabled